|
|
楼主 |
发表于 2019-1-14 22:57:14
|
显示全部楼层
The much sought after ML10 used the original Tannoy SRM-B/SGM-B 10" Dual-Concentric rolled-rubber-surround paper cone driver with the Mastering Lab Crossover. Manley and The Mastering Lab jointly-commissioned the last ever production of this famous driver to build a limited run of the ML10 before Tannoy discontinued the SGM10 p/n 2558R driver around 1992. The beefy, dense, non-resonant cabinet was constructed of 1 1/2" thick MDF finished in black formica with either 1" thick solid walnut or cherry sides. These sides served to protect the corners of the cabinet. (There do exist some early ML10 without the solid wood side bumpers and yes, we observed folks dinging the corners of the formica slamming into walls and doors which is why we added the solid wood side bumpers!)
The Crossover was The Mastering Lab's creation. They had been retro fitting the crossover into little plastic boxes banged on the back of stock Tannoy SRM-B/SGM-B 5/8" ply cabinets before this joint project came to light. The idea was we would design and build strong and heavily braced new cabinets 15" Wide X 10" Deep X 22" Tall weighing in at 50 lbs. each, order the drivers and build Doug Sax's crossover into these ML10's with proper production techniques, all with the crossover controls mounted on the front for the first time, and Bi-ampable/Bi-wireable recessed five way binding posts on the back. The dream speaker was born. People really started crying when they all sold out!
The ML10 offered point source localization combined with absolute time alignment, low distortion and phase coherence. Amplifier power of 100 to 200 watts was recommended. Designed to provide the recording engineer with a highly accurate yet musical tool, the ML10 is now a highly sought after collectible. Used, they are selling for much more than the original retail price of $2950.00 USD. We have seen them selling for over $4000/per pair.
Sooooooooooo.... we created the ML 10A follow-up design to "keep the dream alive". We went on with another then-current production Tannoy 10" Dual-Concentric rolled-rubber-surround paper cone driver (7900-0267) #2598 as found in the 1992-1998 Tannoy Stirling hifi model. A new crossover had to be used with the newer driver to compensate for the different balance of woofer to tweeter efficiency in the newer driver. Approximately 50 pairs of ML10A were produced before we decided to discontinue the ML10A project.
But hope does exist!
12/2018 UPDATE: We do not have any drivers in stock at the moment.
Yes, we do offer to swing YOUR SGM-B/SRM-B 10" drivers into our big beefy ML10 cabinets and install the Mastering Lab Crossovers for $2950 per pair, just like the original ML10. We are currently using a beautiful Mahogany wood with a medium cherry stain sealed with a hand rubbed waxed finish for the solid wood side panels.
We always have plenty of cabinets + TML xovers available if YOU have the drivers. Factory-direct cost is $2950 for the pair of cabinets and TML crossovers (using YOUR drivers). And yes, we also provide the strong shipping cartons and packaging as part of the deal. Email EveAnna Manley for more info.
If we are installing your drivers in our cabinets, you are welcome to ship us the drivers so we can test the whole system with your drivers. But you do not have to. If you prefer not to ship your drivers to us, we can test them with a set of drivers from our ML10's that we use in our QC room and you can screw in your drivers yourself. Four allen bolts and a Molex plug and you have installed your driver.
NOTE: We cannot sell you the crossovers on their own to put in your Tannoy cabinets. We only offer TML xovers complete in our cabinets as a whole system.
Email EveAnna Manley for more info, or to get your name allocated to a pair of ML10 cabinets.备受追捧的ML10使用了原装的Tannoy SRM-B / SGM-B 10“双同​​心滚动橡胶环绕纸锥驱动器和Mastering Lab Crossover.Manley和The Mastering Lab联合委托了这个着名的最后一次生产在Tannoy于1992年左右停止使用SGM10 p / n 2558R驱动器之前，为了制造限量版ML10，该车型为强劲，坚固，密集，非共振的机柜由1 1/2“厚的MDF制成，表面处理为1”厚坚固的核桃或樱桃两侧。这些侧面用于保护柜子的角落。（确实存在一些没有实木侧面保险杠的早期ML10，是的，我们观察到人们撞到了窗户的角落撞到了墙壁和门，这就是为什么我们添加了实木侧保险杠！）
Crossover是The Mastering Lab的创作。在这个联合项目曝光之前，他们已经将这款交叉装置改装成了装在Tannoy SRM-B / SGM-B 5/8“板式机柜背面的小塑料盒。我们的想法是我们会设计和建造强大的支撑新机柜15“宽X 10”深X 22“高重50磅。每一个，订购驱动程序，并使用适当的生产技术将道格萨克斯的分频器构建到这些ML10中，所有这些都是首次安装在前面的交叉控制器，背面安装有双功放/双线嵌入式五向接线柱。梦想演说家诞生了。当他们全部售罄时，人们真的哭了起来！
ML10提供点源定位，结合绝对时间校准，低失真和相位相干性。建议放大器功率为100至200瓦。 ML10旨在为录音工程师提供高度准确的音乐工具，现在是备受追捧的收藏品。使用时，它们的售价远远超过2950.00美元的原始零售价。我们看到他们每双售价超过4000美元。
Sooooooooooo ....我们创造了ML 10A后续设计，以“让梦想保持活力”。我们继续使用当时生产的另一款Tannoy 10“双同​​心滚动橡胶环绕纸锥驱动器（7900-0267）＃2598，在1992-1998 Tannoy Stirling高保真模型中找到。一个新的交叉必须使用更新的驱动器，以补偿新型驱动器中低音扬声器与高音扬声器效率的不同平衡。在我们决定停止ML10A项目之前，已生产了大约50对ML10A。
但希望确实存在！
12/2018更新：目前我们没有库存的任何司机。
是的，我们提供将你的SGM-B / SRM-B 10“驱动器摆放到我们强大的ML10机柜中，并以每对2950美元的价格安装Mastering Lab Crossovers，就像最初的ML10一样。我们目前正在使用美丽的桃花心木中等樱桃渍，用手工打磨的蜡质表面密封，用于实木侧板。
如果您有驱动程序，我们总是有足够的机柜+ TML xover。这对机柜和TML分频器（使用您的驱动程序）的工厂直接成本为2950美元。是的，我们还提供强大的运输纸箱和包装作为交易的一部分。发送电子邮件至EveAnna Manley获取更多信息。
如果我们在您的机柜中安装您的驱动程序，欢迎您向我们发送驱动程序，以便我们可以使用您的驱动程序测试整个系统。但你没必要。如果您不想将您的司机运送给我们，我们可以使用我们在QC房间使用的ML10中的一组驱动程序对它们进行测试，您可以自行拧入您的驱动程序。四个艾伦螺栓和一个Molex插头，你已经安装了你的驱动程序。
注意：我们不能将自己的分频器卖给你的Tannoy橱柜。我们只在整个系统的机柜中提供完整的TML xover。
向EveAnna Manley发送电子邮件以获取更多信息，或者将您的名字分配给一对ML10机柜。
|
|
公安部备 45010302002201
客服：18077773618
发表于 2019-1-14 22:19:42
